Super Wet Look® Paver Sealer From Seal ‘n Lock

Super Wet Look® Paver Sealer from Seal n Lock is a high solids, two-part water based pure urethane sealer that penetrates the pavers to provide a longer lasting protective barrier with superior joint stabilization (no need for polymeric sand) resulting in a ‘wet’ look.

Super Wet Look® is user friendly and environmentally safe. The high solids content of pure urethane wears evenly and lasts longer than solvent based sealers.

Super Wet Look® is available in 2 gallon and 5 gallon kits.

Super Wet Look® Benefits

  • Two Part Urethane
  • Superior Joint Stabilization
  • “Wet Look” Shine
  • Inhibits Algae & Mold Growth
  • Enhances Colors

All Seal ‘n Lock products are made of the most environmentally-friendly products available, and offer excellent weatherability, UV protection, and help prevent algae and mold. All of our cleaning and sealing products and specialty coatings are VOC compliant in all 50 states, and exceeds all hardscape product manufacturers minimum standards guidelines.

eco-friendly-seal-n-lock

ESTIMATING GUIDE:

Typically, the application rate will vary from 150 to 200 sq. ft. per gallon, although this rate will vary depending on the texture, absorption rate of the surface and the width of the paver joints.

DIRECTIONS FOR USE:

We recommend wearing protective goggles and latex gloves. For best results, apply Super Wet Look® at temperatures between 60° F and 90° F. In cooler conditions, the sealer should be warmed to approximately 70° F. Do not apply if surface or ambient temperature s below 50°F. A test for compatibility, penetration and adhesion is recommended. If the temperature is going to drop below freezing (32° F) make sure sealer has time to cure.

MIXING:

Super Wet Look® is a 2 part urethane which comes packaged in a 2-gallon kit (3 ½ gallon pail) and a 5-gallon kit (6-gallon pail). Part B (metal container) is cradled inside of Part A (pail). Part A and Part B require mixing and stirring (2 minutes) prior to use. Super Wet paver sealer can be diluted, after mixing with up to 2 parts water and 1 part sealer and makes up to 15 gallons. After mixing, the product must be used within two (2) hours and cannot be stored for future use.

DRYING TIME:

Super Wet Look® sealer will normally dry in sunny areas within approximately 1 hour. Shaded areas, lower temperatures or high relative humidity will slow the drying process. The surface may be open to foot traffic in 4 hours and to vehicular traffic in 48 hours. To minimize tire marks, vehicles should not make sudden stops or tight turns.

CLEANUP:

  • Immediately flush and agitate pump system after sealing with a mixture of 3 gallons water and 8 ounces of pine sol
  • Flush out the pump system with 5 gallons of fresh water – 1 gallon every 5 minutes
  • Always run water through the pump the next morning to have it ready for use
  • View Seal ‘n Lock Pail Pump Cleanout Instructions

NOTES:

  • Pavers with high absorption rate will require additional top coats of sealer to provide a protective barrier and desired enhancement.
  • Super Wet Look® is not intended for submerged surfaces.

MAINTENANCE:

Periodic washing of pavers with a mild detergent to keep the area clean is recommended.

DO NOT USE ACIDSGasoline, hydraulic fluids and motor oil spills should be removed from the surface of the pavers as soon as possible. We recommend that surfaces previously sealed with Super Wet Look® should be cleaned and resealed every 3 years, depending on environmental exposure and traffic.

CAUTION: Too many coats of sealer may induce a slippery condition. May be slippery during the application if walked on. May cause skin and eye irritation. Do not take internally. Wear mask. All label directions should be read thoroughly before use.